Microlift学

行业概念

小白导读 · 解释

跟工厂工程师或者老客户聊几句,他们嘴里会蹦出一串你没听过的词:载荷中心、自由提升、AST、龟速模式……他们默认你都懂,不会停下来给你解释。这一章就是把这些“默认你懂”的行业黑话,一个个翻译成人话。比如自由提升,说的是门架不整体变长、货叉先自己往上升,进集装箱的时候特别有用;龟速模式就是一键把车放慢,方便精细对位。记住这些词,下次再听到有人随口说出来,你不用再当场懵一下、事后偷偷去查。

读完这章你能听懂工厂工程师和老客户随口说出的行业黑话,不用再假装听懂。

客户和工厂工程师都默认你懂这些词。

Both customers and factory engineers will assume you already know these terms.

载荷中心Load center
货物重心到叉根的距离。搬运车按 600mm 标定,堆高车和叉车按 500mm。货越长,重心越远,实际承载越低。
载荷曲线Load curve
不同起升高度、不同载荷中心下的实际允许载重。铭牌上的额定载荷只在低位成立;客户问“能举多重”必须同时问举多高。
通道宽度AST
车带着托盘直角转弯所需的最小巷道宽度,决定车能不能进客户仓库。样本分 1000×1200 和 800×1200 两种托盘给值。
转弯半径Wa
车体最外点的转弯半径。三支点叉车 (FTB) 明显小于四支点 (FB)。
自由提升Free lift
门架总高不变的情况下货叉能升的高度。集装箱内、低矮库房作业必须选全自由提升门架,否则一起升门架就顶到箱顶。
Fork-over 与 Straddle
前者支腿在货叉正下方,只能叉底部开放的托盘;后者支腿在两侧,能叉川字、田字等封闭托盘。
爬坡度Gradeability
分满载和空载两个值,单位是 %。客户常说“度”,5° 约等于 8.7%。
LFP
磷酸铁锂。锂电里热稳定性最好的一类,循环寿命长。
VNA 模式与直立行走
窄巷道模式。手柄竖直时也能低速行走,用于空间极小的场合。
龟速模式Turtle mode
一键限速,用于精细对位。客户投诉“车变慢了”先查这个。
EPS
电子助力转向,ET 和 ES16 系列标配,低速转向轻。
OPS
离座感应保护。操作员离座后切断行走和起升。
Load CenterLoad center
The distance from the cargo's center of gravity to the base of the forks. Rated at 600mm for pallet trucks, 500mm for stackers and forklifts. The longer the load, the farther the center of gravity, and the lower the actual capacity.
Load CurveLoad curve
The actual allowable load at different lift heights and load centers. The rated capacity on the nameplate only applies at the lowest position; when a customer asks "how much can it lift," always also ask "lift to what height."
Aisle WidthAST
The minimum aisle width needed for the truck, carrying a pallet, to make a right-angle turn — this determines whether the truck can fit into the customer's warehouse. The spec sheet gives values for both 1000×1200 and 800×1200 pallets.
Turning RadiusWa
The turning radius of the outermost point of the truck body. 3-wheel forklifts (FTB) are noticeably smaller than 4-wheel ones (FB).
Free LiftFree lift
The height the forks can rise while the overall mast height stays the same. Inside containers or low-ceiling warehouses you must choose a full free-lift mast, otherwise the mast itself will hit the ceiling as soon as it lifts.
Fork-over and Straddle
The former has its legs directly under the forks and can only fork pallets that are open underneath; the latter has legs on both sides and can fork closed pallets (with solid or cross-runner bottoms).
GradeabilityGradeability
Given as two values — loaded and unloaded — in %. Customers often say "degrees"; 5° is roughly equal to 8.7%.
LFP
Lithium iron phosphate. The most thermally stable type of lithium battery, with a long cycle life.
VNA Mode and Upright Walking
Very-narrow-aisle mode. The truck can still creep forward at low speed even with the tiller upright, for extremely tight spaces.
Turtle ModeTurtle mode
A one-button speed limiter for fine positioning. If a customer complains "the truck got slow," check this first.
EPS
Electric power steering, standard on the ET and ES16 series, making low-speed steering light.
OPS
Operator-presence sensing protection. Cuts off drive and lift the moment the operator leaves the seat.
原理示意图 · 解释
500mm · 额定 1000kg@500mm → 允许载重 ≈ 1000kg
载荷中心示意图 Load center侧视图:货叉上一个货物方块,滑块移动货物重心位置,展示重心越远允许载重越低的杠杆原理。载荷中心 500mmLoad center
示意,实际以载荷曲线为准:货的重心(载荷中心)离叉根越远,能举的重量越小。
原理示意图 · 解释
载荷曲线示意图 Load curve chart折线图,横轴载荷中心,纵轴允许载重,两条阶梯线分别代表较低和较高两个起升高度;三个编号标注读图顺序:先找起升高度,再找载荷中心,最后读允许载重。4005006007008009001000050010001500允许载重 (kg)Allowed load载荷中心 (mm)Load center起升 3.0m起升 4.5m123
读图三步:① 先按起升高度选曲线 ② 在横轴找载荷中心 ③ 竖线与曲线交点对应的纵轴读数就是允许载重。
原理示意图 · 解释
Fork-over 与 Straddle 支腿对比示意图俯视图,左边 fork-over 支腿在货叉正下方,靠近封闭(田字)托盘时会撞上托盘边缘;右边 straddle 支腿在两侧,能绕开托盘继续前进。✕fork-over:支腿在货叉正下方Legs under forks✓straddle:支腿在两侧绕开Legs straddle outside
封闭(田字)托盘底部没有支腿能钻进去的空当:fork-over 支腿会顶死,straddle 支腿从两侧绕过去。
原理示意图 · 解释
自由提升示意图 Free lift两个集装箱侧视轮廓对比:左边普通门架起升时内门架整体升高会顶到箱顶,右边全自由提升门架总高不变,只有货叉单独升起。集装箱顶Container roof✕内门架升起会超出箱顶Inner mast exceeds roof集装箱顶Container roof✓门架总高不变,只升货叉Mast height fixed
集装箱、低矮库房作业要选全自由提升门架,否则一起升,门架顶部就会先顶到箱顶。
原理示意图 · 解释
所需通道 ≈ 1951mm
通道宽度示意图 Aisle width (AST)俯视图:一辆车带着 1000×1200 托盘直角转弯进入货架,两条虚线间的宽度就是所需的最小通道宽度,随所选车型变化。货架Rack所需通道 ≈ 1951mm
示意,实际以样本 AST 参数为准;非标托盘需用公式换算(见售前核算章节)。
原理示意图 · 解释
8% ≈ 4.6°
爬坡度示意图 Gradeability直角三角形表示坡道,滑块调节坡度百分比,同时显示换算出的角度,并列出满载能爬上这个坡度的车型分组。坡度角 4.6°坡道 Ramp8%
满载能爬上此坡的车型:T15i / T20iT15 / T20TS12i / TS15iES16 / ES16-SFTB15M / FTB18MFTB15 / 18 / 20FB15 / FB18FB20 / FB25FB30 / FB35FB20P / FB25PFB30P – FB40PFB50P
爬坡度是满载/空载分别给的两个值,单位 %;客户说“5 度”约等于 8.7%。
本章思维导图
行业概念 思维导图载荷中心载荷曲线承重相关通道宽度AST转弯半径自由提升空间相关Fork-over支腿在叉下Straddle支腿在两侧托盘相关爬坡度龟速模式窄巷道VNA行驶与速度EPS电子助力转向OPS离座保护安全与转向行业概念